Trusted by Industry Leaders Worldwide

Products Category

Products


 : +86-750-3652251 / 3856396

: +86-750-3856395 / 3856397

: www.dndhardware.com

: sales@dndhardware.com

 

How to Measure an Existing Euro Mortise Lock for Replacement

Views: 0     Author: D&D Hardware     Publish Time: 2026-11-20      Origin: D&D Hardware

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
How to Measure an Existing Euro Mortise Lock for Replacement

To measure a Euro mortise lock for replacement, start with the backset and the distance between the spindle and cylinder centres. Then check the faceplate, lock case, and strike. Two locks can share the same centre distance and still put the handle and cylinder in different positions on the door.

This guide is for maintenance teams, door manufacturers, and hardware buyers replacing an existing commercial lock case. It shows where to take each measurement, how to compare it with a supplier drawing, and when to hold an order for further checks.

11

Key Takeaways

  • Measure backset from the exposed face of the faceplate to the centre of the handle spindle opening, using the drawing's reference plane.

  • For a Euro-profile cylinder lock, measure PZ from the spindle centre to the cylinder centre.

  • Check the faceplate recess and fixing holes separately from the pocket that takes the lock case.

  • Confirm the lock function, latch direction, and strike alignment before ordering.

What Should You Record Before Measuring?

Photograph the existing lock from the door edge and both faces. Capture the faceplate markings, lever or handle set, cylinder, and strike. Record the opening ID and how the lock operates from each side. A replacement must suit the way the opening is used as well as the available space.

When comparing European mortise locks, ask for the drawing of the exact function and size you intend to order. To verify hidden dimensions, have the installer identify or remove the case under the site's maintenance procedure. Record which dimensions were measured directly and which came from an older drawing.

European mortise locks

How to Measure the Existing Euro Mortise Lock

Measure Backset and PZ Centres

The backset locates the spindle in from the door edge. For the configuration shown here, measure perpendicular from the exposed face of the faceplate to the centre of the square spindle opening. Use that same reference when reading the replacement drawing. If the door edge is bevelled or rebated, record the face from which you measured.

For a Euro-profile cylinder case, PZ, or centres, is the distance from the handle spindle centre to the cylinder centre. It runs vertically on the layout shown here. Use the cylinder centre indicated on the drawing. A latch-only or privacy case may have a different layout, so record the existing function before assigning a PZ value.

Compare the Faceplate With the Recess

Measure faceplate length, width, and thickness. Note whether the ends are square or rounded. Record the fixing-hole positions from the same end of the plate, and include the centre-to-centre distance between screws. Two plates of the same overall length can use different screw positions.

Compare the proposed faceplate with the existing door-edge recess. If the new plate fits the recess but its screws land outside the original fixing points, flag the difference before ordering. This is particularly important where the door uses a prepared metal reinforcement or fixed threaded holes.

Check the Lock Case and Retained Hardware

Measure the case height, depth behind the faceplate, and thickness. Look for projections that also need space in the pocket. Some drawings show overall depth from the front of the faceplate, so note which reference your figures use before comparing the two.

Check the spindle size and the holes used to fix the lever trim, especially if the screws pass through the case. Mark the trim screw positions separately from the faceplate screws. Even with matching spindle and cylinder centres, a screw may hit the case instead of passing through its fixing hole.

If the cylinder is staying, confirm its profile and compatibility with the proposed lock. Record the swing and hinge side, and photograph the latch bevel. Use the supplier's handing convention when placing the order.

11

How to Decide Whether the Replacement Fits

The D&D DDML009 Euro mortise lock lists 72 mm centres and 55 mm or 60 mm backset. Use both figures when selecting the variant.

What you find What to do before ordering
The existing case has 55 mm backset and 72 mm centres. The 55 mm replacement drawing also matches the pocket, faceplate, fixings, and retained trim. Treat it as a candidate for a like-for-like replacement. Confirm the lock function, handing, and strike before ordering.
The existing case has 55 mm backset and 72 mm centres. The proposed replacement has 60 mm backset and the same 72 mm centres. Request the 55 mm version or ask for another matching case. In this layout, the spindle and cylinder centres would both sit 5 mm farther in from the faceplate.
Backset and centres match, but the case is deeper or the latch and deadbolt sit at different heights. Send the existing preparation and strike dimensions for review. Check whether the case and bolts fit the opening as prepared.

When comparing commercial mortise lock options, check the latch and deadbolt against the frame strike. Record the vertical position and size of each strike opening. On the old and proposed cases, measure from the same end of the faceplate to the latch and deadbolt centres. A change in either position calls for a check against the frame with the door seated.

If the old latch already rubs the strike, record the contact point so the installer can check the door fit as part of the replacement. After installation, verify the required operation from both sides and confirm that the latch and deadbolt engage without forcing the door.

If the project specifies an EN 12209 mortise lock, check the applicable performance documentation against BS EN 12209 and use the model drawing to confirm fit. On a rated opening, verify the replacement against the door assembly documentation. Consult the Steel Door Institute's fire door guidance before making changes to an existing steel fire door.

EN12209 Mortise Lock-D&D Hardware

What to Send the Supplier

Send one record per opening when the site uses more than one lock. Label the measurements so the supplier can distinguish, for example, 55 mm backset from 72 mm centres.

Item What to send
Lock identification Opening ID, model markings, and the required lock function
Main dimensions Backset, PZ where applicable, and case height, depth, and thickness
Door preparation Faceplate length, width, thickness, end shape, and fixing-hole positions
Hardware to retain Lever trim, spindle, cylinder, handing details, and photos of the strike

On the sketch, mark the reference face and identify the parts that must stay. If the existing trim and strike must be reused, state that in the request. Ask the supplier to confirm the size variant and identify any dimension that still needs a site check.

Conclusion

Start with backset and centres, then compare the faceplate, case, trim, and strike against the proposed model drawing. A complete record lets the supplier confirm the correct variant before the lock arrives on site.

Need help matching an existing lock case?
Send D&D Hardware the measurements and photos of the old case, door edge, and frame strike.
Request a mortise lock replacement review.

11

FAQ

Can I Measure a Euro Mortise Lock While It Is Still in the Door?

You can record visible centres, the faceplate, and its fixing holes while the lock is installed. Use the original drawing or have the installer expose the case to verify hidden dimensions.

Is Backset the Same as Mortise Lock Case Depth?

Backset ends at the spindle centre. Case depth ends at the back of the body. Record the reference face for each measurement.

Can I Keep the Old Cylinder With a New Euro Mortise Lock?

Ask the supplier to confirm the profile and cam compatibility. Check the cylinder length and its position relative to the retained trim and door faces.

What if I Cannot Find the Old Lock's Model Number?

Send clear photos and a dimensioned sketch. Include the latch bevel, spindle arrangement, cylinder opening, and how the old lock works from both sides.

Should I Measure the Strike if I Am Replacing Only the Lock Case?

Yes. The strike stays in the frame, so check where the new latch and deadbolt will meet its openings. Include a photo that shows the strike and the surrounding frame.

Contact us Now:

Contact: David Jian

Mob:0086-139 2903 7292

Email: David@dndhardware.com, sales@dndhardware.com,

Contact: Jobby Zhang

Mob:0086-137 2599 9617

Email: jobby@dndhardware.com


D&D HARDWARE INDUSTRIAL CO.,LTD  

ADD:12th Floor, Building 2, No.898, KeChuang Technical Zone, Jiangmen Avenue, Pengjiang District, Jiangmen City, Guangdong, China (Postcode:529000)

https://www.dndhardware.com

Tel: +86-750-3856396

Fax: +86-750-3856395


Contact Info

:+86-139 2903 7292   David Jian

: +86-750- 3856396

 : sales@dndhardware.com
 
 timg: +86-139 2903 7292
 
 : +86-139 2903 7292

:  12th Floor, Building 2, No.898, KeChuang Technical Zone,
Jiangmen Avenue, Pengjiang District, Jiangmen City, Guangdong, China
      
Get Famous Branded Quality at Factory Cost
©Copyright D&D HARDWARE INDUSTRIAL Co., LIMITED. All Rights Reserved.